Maytag, Range, and Oven Repair
       

(877) 309-7770

  

Maytag, Range, and Oven Repair

Service, maintenance and authorized Maytag repair

If you need routine maintenance, authorized repair and even service on your Maytag, call us today. Maytag dryer Repair Authorized Service in Los Angeles has the professional technicians to get the job done right. If your Oven needs repair service. If your Oven, range, or cook top needs repaired give us a call today. We have Factory Trained authorized technicians in your area standing by to serve you better.

We can repair and service all models of Maytag, Whirlpool, Maytag, GE, Maytag, Samsung, Maytag, Kitchenaid, frigidaire, hotpoint, and many more brands of Oven repair services, Electric Oven, Gas Oven, Steam Oven, and Stackable Oven.

Trust your appliance repair to our team of factory trained expert technicians. Call us today to schedule and appointment, or use our online form. We thank you for the opportunity to serve you.

Maytag Range/Stove/Oven

Failure
Code
Condition
Check/Repair
F1
Defective touch pad or membrane
Replace touch pad or membrane (usually the touch pad)*
F1
Watchdog on board
Replace touch pad or clock assembly (also called the ERC)
F2
Oven too hot
Replace relay board (if present) or bad oven temperature sensor
F3 or F4
Open or shorted oven temperature sensor
Replace oven temperature sensor
F5
Hardware and watchdog circuits disagree
Replace clock assembly (also called the ERC)
F6
Missing AC signal
Check for proper voltage
F7
Function key shorted or stuck button
Replace touch pad or clock assembly (also called the ERC) or un-stick button
F8
Analog/Digital supervisory
Replace clock assembly (also called the ERC)
F9
Door latch supervisory
Check door lock circuit or replace clock assembly (also called the ERC)
F0
Function key stuck
Replace touch pad or clock assembly (also called the ERC)
* Here is a simple test that you can do to determine whether the clock or the touchpad are defective when the display reads F1: 

- Disconnect power to the range.
- Gain access to the back of the ERC (electronic range control, or "clock"). 
- Unplug the touch pad ribbon connector from the ERC. This will be a flat wire about 1 ½" to 2" wide.
- Make sure everything is clear and will not short out when power is turned back on. Replace any covers removed to gain access to the ERC.
- Turn the power back on to the range. 
- Watch for the F-1 and listen for the beep. 
- If you get the F-1 and beep, replace the ERC. 
- If after approximately 60 Minutes you do not get the F-1 fault, replace the touch pad. 

NOTE: Some models incorporate the touch pad and the clock control as one part so F1 = bad clock control. 

Warning: If you do not feel comfortable doing this test or making this repair please contact a qualified appliance repair technician.

 

Maytag Type "C" and "D" Clocks Range/Stove/Oven Fault Codes

Failure
Code
Condition
Check/Repair
F1
Supervisory relay enable shorted (non-cook mode); sounds alarm and inhibits cook mode if alarm fault monitor is always active in non-cook mode, and requires removal of power until serviced.
Usually a bad touch pad or clock assembly (also called the ERC). Replace touchpad or ERC
F2
Bake/broil/clean temp runaway alarm; sounds alarm and resets control to non-cook mode when bake/broil/clean temp exceeds programmed limits.
Usually means a stuck relay. Electric @ 525F (bake), 640F(broil), 900F(clean) 

Gas @ 525F (bake), 640F(broil), 900F(clean)
F3
Open temp oven temperature sensor; sounds alarm and inhibits cook mode
Replace oven temperature sensor
F4
Shorted temp oven temperature sensor; sounds alarm and inhibits cook mode
Replace oven temperature sensor
F5
Supervisory relay enable open (cook mode); sounds alarm and resets the control to non-cook mode
Replace electronic range control (ERC)
F5
Missing a/c line cycle detector; displays code (no audible)
Unplug appliance for two minutes, should clear problem
F7
Function key shorted; too hot at the clock assembly (also called the ERC) or shorted touch pad or clock assembly (also called the ERC)
Replace touchpad or ERC
F8
Analog/Digital supervisory; sounds alarm to non-cook mode
Replace ERC
F9
Door latch supervisory (door latched)
Unlock door and check switches or clock assembly (also called the ERC)
F0
Cancel key supervision
Requires the removal of power until serviced. See qualified technician

 

Maytag Stackable A/W Washer & Dryer Fault Codes

Failure
Code
Condition
Check/Repair
"L" persists in washer display
Lid lock failure
Replace switch, linkage, lock solenoid or control board.
1E persists in washer display
Lid lock failure
Replace lid lock switch or control board.
9E appears in dryer display
Door switch failure
Check door switch wiring or door switch or control board
"U" occurs for no reason in display
Unbalanced load
Unbalance switch or control board
6E appears in dryer display
Temp control error
Ambient (room) temperature too cool, -or-
· thermistor
· wire harness
· control board
7E appears in dryer display
Temp control error - overheating
Check:
· venting for restriction
· thermistor
· control board
· cycling thermostat (regular)
8E appears in dryer display
Motor relay circuit
Check:
· relay coil
· wire harness or
· control board

 

We repair and service these appliances.

Oven Repair
Range Repair
Cook Top Repair

frigidaire

frigidaire
frigidaire